Armada GFL3000 Ground Fault Locator

 

Armada GFL3000 Ground Fault Locator

 

 

The Armada Technologies GFL3000 Ground Fault Locator is designed to find wire or cable damage that results in an electrical path to ground. The GFL3000 works on the principle of earth gradient theory and is sometimes referred to as an earth gradient fault detector. The GFL3000 will pinpoint the exact location of a grounded cable fault. The GFL3000 is NOT a cable path locator. You will likely need a separate cable locator to locate the path of the entire cable.

How it Works – The GFL3000T transmits a voltage charge in succession approximately every 2 seconds. The charge is applied through the leads and into the connected cable where they travel to the ground fault. At the ground fault, some of the electrical current leaks to earth ground. This amount is

The receiver/A-frame is then inserted into the ground along the path of the wire. As the current flows down the wire, it travels out through the ground fault and then back to the ground stake. Some of this current, however, travels through the A-frame receiver. The needle at the top of the A-Frame will give a directional kick either left or right. The initial kick direction is the one that determines the direction. Usually after this intial kick, the needle will rebound in the opposite direction. Only the initial kick is important.

The receiver determines which side of the frame received the current first and therefore, which direction the fault lies. By relocating the frame, the user can zero in as to exactly where the fault lies.

Batteries – The GFL3000 transmitter uses a 12v rechargeable battery (included). There are also 110v AC and cigarette lighter rechargers included for this battery. The battery comes disconnected in shipping. To connect the battery, remove the finger screws located on each side of the transmitter control panel. Inside the compartment, you will see the battery and 2 connecting terminals using spade clips. Carefully remove the rubberized terminal covers and connect the spade clipped wires to the battery. Replace the cover and tighten the screws.

To recharge the transmitter battery, connect the charger to the charging receptacle on the transmitter and then plug into a wall outlet. The battery level indicator on the transmitter face will indicate the amount of charge in the battery.

The receiver module that sits atop the frame requires (1) 9V battery. Remove the screws on each side of the receiver and remove the cover. Tightly connect the 9v square battery to the battery boot and replace the cover.

 

 

LeCroy WaveAce 1000 and 2000 Oscilloscopes

 LeCroy WaveAce Oscilloscopes 40 MHz – 200 MHz

 LeCroy WaveAce Oscilloscopes 40 MHz – 200 MHz

THE TOOLS AND FEATURES FOR ALL YOUR DEBUG NEEDSA good oscilloscope should simplify how you work and shorten the time it takes to find and debug problems. The WaveAce™ combines long memory, a color display, extensive measurement capabilities, advanced triggering and excellent connectivity to improve troubleshooting and shorten debug time. With bandwidths from 40 MHz to 200 MHz, sample rates up to 2 GS/s and waveform memory up to 10 kpts/Ch (20 kpts interleaved) the WaveAce exceeds all expectations of a small affordable oscilloscope.Digital Filter
Digital filtering is available on each channel of the WaveAce. The Low-Pass, High-Pass, Band-Pass and Band-Stop filters allow you to isolate only the frequencies you want to see.Trigger
Edge triggering is not always the best choice for every signal. Beyond the basic edge trigger is a set of trigger capabilities which include Pulse Width, Video and Slope (Rise Time) triggers.

Long Capture and Zoom
Small, portable oscilloscopes often suffer from short capture time due to the small waveform memory. The WaveAce is available in 4 kpts/Ch and 10 kpts/Ch configurations which is up two to three times more than competitive products. More memory results in longer capture times showing more waveform detail with each trigger. Activate the built-in zoom function to take a closer look at the details.Automatic Measurements
With 32 standard automatic measurements the WaveAce simplifies how you work. Display up to five measurements without crowding the waveform display or show all 32 at once with the measurement dashboard. A wide range of advanced timing parameters provide insight to the relationship between two different signals.Waveform Math
The WaveAce provides five math functions including Add, Subtract, Multiply, Divide and FFT. The FFT capability includes the choices of four windows and two different vertical scales.Connectivity
The WaveAce provides a USB host port on the front panel for saving screen images, waveforms and setups to a memory stick. A rear panel USB device port allows for connection to a PC or printer. Connecting and communicating with a PC is simplified with EasyScope software providing full access to the oscilloscope’s display, measurements, waveform data and front panel controls.

Pass/Fail Test
With built-in Pass/Fail Mask testing the WaveAce can quickly identify problems and let you know when they occur. A history of the P/F results can be displayed on the screen.

Waveform Sequence Recorder
Capture and replay a sequence of up to 2500 waveforms to isolate that runt or glitch which is causing problems in your system.

Large Internal Storage
Saving and recalling waveforms and setups from internal memory can save a lot of time during test and debug. The WaveAce can save up to 20 waveforms, 20 setups and two reference waveforms to the internal memory.

Acquisition Modes
Different applications call for different acquisitions modes. The WaveAce offers Real Time, Equivalent Time, Peak Detect and Averaging modes to ensure that any waveform can be captured and displayed.

Click here for more related items!

LeCroy WAVEACE 2012 100 MHz 2 Channel Digital Oscilloscope

 LeCroy WAVEACE 2012 100 MHz 2 Channel Digital Oscilloscope

 LeCroy WAVEACE 2012 100 MHz 2 Channel Digital Oscilloscope

A good oscilloscope should simplify how you work and shorten the time it takes to find and debug problems. The WaveAce™ combines long memory, a color display, extensive measurement capabilities, advanced triggering and excellent connectivity to improve troubleshooting and shorten debug time. With bandwidths from 40 MHz to 300 MHz, sample rates up to 2 GS/s and waveform memory up to 1 Mpts/Ch (2 Mpts interleaved) the WaveAce exceeds all expectations of a small affordable oscilloscope.

Measure and Debug Tools
With 32 automatic measurements standard, the WaveAce simplifies how measurements are made. The large 7” widescreen display can show up to five measurements without crowding the waveform display or show all 32 at once with the measurement dashboard. A wide range of advanced timing parameters provide insight to the relationship between signals on two different channels. WaveAce oscilloscopes provide five math functions for additional analysis including Add, Subtract, Multiply, Divide and FFT. The FFT can be viewed using four different windows and two different vertical scales for an insightful view of the frequency domain. Built-in Pass/Fail Mask testing allows for quick identification of problems and highlights when they have occurred.

Easy to Use for Faster Debug
The high performance and large feature set of the WaveAce is controlled by an intuitive user interface with 11 different languages and a streamlined front panel. All important controls and menus are accessed from the front panel with a single button press. All position and offsets can be reset by simply pressing the knob, pressing the V/Div knob will switch between fixed and variable gain and pressing the T/div knob will toggle between zoom modes. Buttons on the front panel that open and close menus or switch modes, are backlit so that the mode of operation is easily visible to the user.

Click here for more related items!

Weller KDS808 Shot Meter with Vacuum Only

Weller KDS808 Shot Meter with Vacuum Only

 

 

Basic shot meter with a vacuum pullback to prevent dripping, and foot pedal actuation to permit hands-free operation. Requires shop air (80-100 psi) to operate. Operates on 115V.

For use with air-operated dispensing applications featuring a vacuum pullback system to prevent dripping. Operates at 110VAC and comes complete with instructions and a plug-in foot pedal.

 

 

Weller KDS824A Meter Shot Delux

Weller KDS824A Meter Shot Delux
Dispenses low, medium and high viscosity adhesives, liquids and epoxies.

 

 

The Weller KDS824A Economy Bench top Shot Meter w/ Foot Pedal is a precision tool used to give trouble free service under normal conditions and dispenses materials into a syringe using a syringe adapter. This bench top unit provides easy identification of dials, adjustment of air pressure, vacuum and also has a digital timer control, which allows metered shot repeatability. It also comes provided with an electronic actuated foot pedal for a more controlled dispensing of material that can have a shot time duration between 0.01 to 99.99 seconds. The KDS834A also features adjustable four position push button timer switch and is a low voltage unit that can be easily switched from 115 volts to 230 volts with a slide of a switch.

 

 

Weller KDS834A Economy Shot Meter

Weller KDS834A Economy Shot Meter
Dispenses low, medium and high viscosity adhesives, liquids and epoxies.

 

 

The Weller KDS834A Economy Bench top Shot Meter w/ Foot Pedal is a precision tool used to give trouble free service under normal conditions and dispenses materials into a syringe using a syringe adapter. This bench top unit provides easy identification of dials, adjustment of air pressure, vacuum and also has a digital timer control, which allows metered shot repeatability. It also comes provided with an electronic actuated foot pedal for a more controlled dispensing of material that can have a shot time duration between 0.01 to 99.99 seconds. The KDS834A also features adjustable four position push button timer switch and is a low voltage unit that can be easily switched from 115 volts to 230 volts with a slide of a switch.

 

 

Gossen Metrawatt SecuTest Series Electrical Equipment Safety Tester

Gossen Metrawatt SecuTest Series Electrical Equipment Safety Tester

 

Test Instrument per BGV A3 (previously VBG 4), MPG (medial product law) and for routine and type tests

Universal tester for testing the electrical safety of portable electrical equipment used in commercial and medical applications, for post-manufacturing tests, testing after repair and for periodic testing.

The SECUTEST SIII+. . .test instruments can be configured for international utilization. The test socket, user interface language and the desired test regulation can all be configured to this end.

Universal test instrument for testing the electrical safety of:

  • after repair and for periodic testing of electrical devices in accordance with DIN VDE 0701-0702:2008
  • after repair and for periodic testing as well as for technical safety checks of electrical medical devices per IEC 62353 (VDE 0751-1) and/or DIN EN 60601 on the basis of the MPG1)
  • in the production of:
    • electrical measuring, control and laboratory devices per DIN EN 61010
    • data processing systems per DIN EN 60950
    • electrical medical devices per DIN EN 60601
    • household appliances per DIN EN 60335

Applications

Testing for the Electrical Safety of Electrical Equipment in Accordance with BGV A3

The test instrument can be utilized for quick and safe testing of repaired or modified electrical devices and as well as for periodic testing in accordance with DIN VDE 0701-0702:2008.

  • Protective conductor resistance
  • Insulation resistance
  • Protective conductor current for SC1 devices
  • Contact current for SC2 devices
  • Absence of voltage at exposed conductive parts (= contact current)

Measuring methods for leakage current measurements:

  • Direct measurement
  • Equivalent leakage current
  • Residual current

Testing for the Electrical Safety of Electrical Medical Devices in Accordance with the German Medical Product Law (MPG) and the associated Operator’s Regulations

The test instrument with feature KA01 is used for quick and safe testing and measurement of repaired or modified electrical medi- cal devices or their components (e.g. patient ports) in accordance with IEC 62353/DIN EN 62353 (VDE 0751) and EN 60601, see also SECULIFEST oder SECULIFE ST HV.

Observance of technical safety requirements allows the user of the test instrument to operate electrical medical devices in a hazard-free fashion. The safety of the patient is also assured through the use of tested electrical medical devices.

Data Cable Transmission Tester
Gossen M7010 SecuTest SIII+Electrical Equipment Safety Tester
Gossen M7010B11C01 SecuTest SIII+Electrical Equipment Safety Tester
Gossen M7010-V013 SECUTESTSIII+HElectrical Equipment Safety Tester with 6kV DC High-voltage

 

 

Dweyer TIC Series Thermal Imaging Camera

TIC Series Thermal Imaging Camera

 

 

The Series TIC Thermal Imaging Camera allows users to see heat contrasts to prevent plant equipment failures, detect air leaks in buildings, and many more applications. Infrared radiation is given off by objects according to how warm they are, and the camera translates the measured levels into visual light on the bright 2.5″ 160 x 120 resolution LCD. For increased differentiation among temperatures, the camera can automatically adjust the color band for a narrower range of temperatures throughout the –4 to 482°F ( -20 to 250°C) temperature range of the camera. Besides taking spot measurements, the camera can also be set for isothermal, area, or profile analysis. All cameras include a Li-Ion battery, battery charger, docking station, SD memory card, SD memory card reader, sun shield, lens cap, video cable, standard reporting software, and a calibration report. A Bluetooth® earphone and USB cable are also included in TIC-30 units for making voice annotations and real time recording.

Up to 9 movable temperature spots can be selected to get specific temperature measurements of objects on the display. On the TIC-20 and TIC-30, there are flash, visual light camera, and a laser pointer to help identify the objects in the picture better. The visual image can be blended with the thermal image for better illustration of where the hot or cold spots are in the image.

FLIR DM93 True RMS Industrial Multimeter with VFD Mode

    FLIR DM93 True RMS Industrial Multimeter with VFD Mode

True RMS Industrial Multimeter with VFD Mode

The FLIR DM93 True RMS Industrial Multimeter is redefining what we come to expect from a digital multimeter. To start with, the DM93 offers advanced VFD filtering to better measure and analyze the non-traditional sine waves and noisy signals associated with variable frequency drive equipment. The DM93 also incorporates a LoZ Mode to reduce ghost voltage for more accurate readings in long runs. Even record data continuously to better understand intermittent problems.

With the FLIR DM93 Multimeter, capturing and analyzing your data has never been easier. Use the integrated Bluetooth functionality to connect to your smartphone or tablet and graph findings in real time. Or just use your phone or tablet to monitor findings from a safe distance in dangerous conditions. The DM93 can also connect to FLIR thermal cameras with MeterLink to capture your electrical and thermal data all in one location for easier analysis.

All the great features of the FLIR DM93 are cased in a rugged black, military style housing. It has a great non slip, weighty feel that matches its impressive capabilities. The screen features large numbers and an LED backlight that can even be read in sunlight. The top of the DM93 has dual bright LED work lights that rival many flashlights, yet won’t eat up battery life. The new FLIR DM93 is an impressive package that, along with the Lifetime Warranty, will offer many years of service to the electrical professional.

LoZ Mode eliminates ghost voltage readings associated with long-run applications. Powerful Worklights eliminate the need for a flashlight while performing tests in dim lighting. Data Record feature captures electrical measurements and provides wireless data transfer. Integrated Bluetooth technology* connects the FLIR DM93 to the FLIR Tools Mobile app on your compatible mobile device. METERLiNK technology wirelessly integrates electrical readings on your infrared image with FLIR Thermal Cameras

Click here for more related items!

FLIR DM92 Industrial DMM with LoZ and VFD Filter

   FLIR DM92 Industrial DMM with LoZ and VFD Filter

The FLIR DM92 RMS Industrial Multimeter is a rugged yet precise 1000V AC/DC multimeter. It offers many of the features of the FLIR DM93 multimeter, yet without the Bluetooth connectivity some users won’t need. The DM92 includes a VFD mode to better analyze the non-sinusoidal waveforms and noisy signals associated with variable frequency drive motors and controllers. The LoZ mode filters out unwanted ghost voltage for better measurement accuracy over long runs. The internal memory of the FLIR DM92 will store up to 99 measurements for later recall and analysis.

The large, crisp display of the DM92 is easy to read, and is assisted in dark areas by a bright LED backlight. A built in stand makes the meter convenient for stationary or bench top work, while two LED work lights brighten those challenging sites. A thick rubberized housing makes the DM92 rugged enough even for the harshest environments. FLIR even backs the FLIR DM92 RMS Industrial Multimeter with a lifetime warranty.

Click here for more related items!